Use the Zaxmote app to wirelessly control Zaxcom Tx sound transmitters linked via a Zaxcom QIFB Bluetooth dongle attached to a Zaxcom QRX receiver. Quickly control transmitter gain, start/stop, and standby settings.
Zaxmote runs on iOS 7 or 8 devices that are equipped with Bluetooth LE (Low Energy): Phone 4S+, iPad, iPod touch 4+. The app works in both landscape and portrait orientations.
Don't have a Zaxcom QIFB Bluetooth dongle yet? You can still use Zaxmote on two iOS devices to take a test drive. Use the Zaxmote's "debugging" mode, and have one iOS device emulate the Zaxcom QIFB. Then run Zaxmote on another iOS device, and connect to the emulated QIFB. From either iOS device, you can then control transmitter gain, rec, stop, and standby settings and see the results on the other iOS device.
－－－－－－－－－－－－－－－－－－－－－－－－－－－－
Test Instructions
－－－－－－－－－－－－－－－－－－－－－－－－－－－－
Install the Zaxmote app on two iOS devices, in close proximity to one another.
Make sure both devices have Bluetooth enabled－－ by placing a finger just below the screen, swiping upward, and ensuring that the Bluetooth icon is white on the "Control Center" screen that appears. Press the "Home" button to dismiss the Control Center screen.
On Device 1:
Run the Zaxmote app by tapping its icon.
Tap the app’s "Connect" button.
On Device 2:
Run the Zaxmote app by tapping its icon.
Enable debugging mode with the "Debugging" switch control.
Tap the app’s "Emulate Bluetooth Dongle" button.
Tap the "Test Data" button to populate the list of Tx units.
Tap a Tx row’s plus/minus buttons to increase/decrease Tx gain.
Tap a Tx row’s gray dot button to toggle its REC/STOP state.
To edit a Tx unit’s data:
Tap the "Edit" button.
Tap on a Tx row.
Enter text into the optional Name, Gain, Frequency fields.
Tap the round-x button in each field to clear its text.
Cleared fields will simulate a QRX that does not send name, gain, frequency, or REC/STOP values to the app.
Back on Device 1:
As the gain, REC, STOP, and POWER buttons are tapped, messages are sent to Device 2, and its updated data is displayed.
使用zaxmote APP无线控制Zaxcom TX声音发射器通过Zaxcom qifb蓝牙适配器连接到一个接收器连接Zaxcom什么。快速控制发射机增益，启动/停止，和备用设置。
zaxmote运行iOS 7或8的设备都配备了蓝牙LE（低能量）：4S手机，iPad，iPod touch 4 +。应用程序在景观和肖像方向。
没有Zaxcom qifb蓝牙适配器吗？你仍然可以使用两个iOS设备zaxmote参加试驾。使用zaxmote的“调试”模式，有一个iOS设备模拟Zaxcom qifb。然后运行另一个iOS设备zaxmote，并连接到仿真qifb。无论是iOS设备，你可以控制发射机增益，REC，停止，和待机设置和其他iOS设备上看到的结果。
－－－－－－－－－－－－－－－－－－－－－－－－－－－－
测试指令
－－－－－－－－－－－－－－－－－－－－－－－－－－－－
在两个iOS设备安装zaxmote APP，在靠近彼此。
确保设备具有蓝牙功能的－－用手指按在屏幕上，刷卡，并确保蓝牙图标是白色的在出现的“控制中心”界面。按下“家庭”按钮，关闭控制中心屏幕。
关于设备1：
通过点击它的图标运行zaxmote APP。
点击应用程序的“连接”按钮。
关于设备2：
通过点击它的图标运行zaxmote APP。
启用“调试”开关控制的调试模式。
开发应用程序的“模拟蓝牙适配器”按钮。
点击“测试数据”按钮，填入TX单位名单。
点击TX排的加/减键增加或减少TX增益。
点击TX行灰度点按钮切换的录制/停止状态。
编辑发送单元的数据：
点击“编辑”按钮。
点击TX排。
将文本输入到可选名称、增益、频率字段。
点击round-x按钮在各个领域明确的文本。
清除字段将模拟一个什么，不发名字，增益，频率，或录制/停止值的应用。
回到设备1：
作为增益，REC，停止，和电源按钮被窃听，消息被发送到设备2，其更新的数据显示。